CO2激光器虚共焦腔凸面镜失调的实验研究

高功率激光器工作时,由于谐振腔反射镜上的光强分布不均匀,会导致镜面温度不均匀,从而造成镜面的角向偏转,致使激光器光轴发生偏转,严重影响输出光束质量,甚至造成不出光。文中主要从实验研究了CO2激光器虚共焦腔凸面镜失调对激光器输出光束质量的影响,实验结果表明,当凸面镜失调角接近于由理论计算而得的失调临界角时,输出光斑约为半个圆环,与理论分析非常符合,当凸面镜失调角达到约为失调临界角的4.5倍时,完全停止振荡。     

应用于引信遥控装定的火控信息交联装置

自差式多普勒无线电引信发射和接收装置是引信遥控装定的重要内容.在装置中引入单片机和FPGA技术,能快速、准确的装定已经出炮口300 ms以上的密集弹药,选择工作方式,可供选择的工作方式有近炸、碰炸、遥控炸、定时(距)炸.引信具备近目标发射电磁波功能,能有效抗有源干扰、海杂波干扰和信道干扰.FPGA的高度集成特性减小了编码和解码、调制与解调电路的体积,减小了引信工作电路.     

基于动力学模型的柔性加工设备机电系统状态监测与故障预警

在建立的加工设备机电系统精确动力学模型及对模型参数实时辨识的基础上［１］，建立柔性加工设备机电系统的状态监测模型，包括ＢＡＹＥＳ故障检测、突发故障检测及故障分析与定位等；同时利用Ｋｕｌ－ｂａｃｋ信息距离和多层递阶ＡＲ模型实现系统的状态与故障预警。在加工设备上的实验表明模型可行有效，它能排除柔性多变工况、时变性及随机干扰对监测与预警功能的影响，提高其鲁棒性和自适应能力。     

Parametric study of single confined fragment launch explosive device

In this article, parametric study of single confined fragment launch device was carried out. The configuration proposed was further studied to derive the empirical relationship for effect of fragment size, charge size, confinement thickness on fragment velocity. The simulations were carried out using ANSYS-AUTODYNE explicit solver. Fragment velocities were estimated as a function of different parametric combinations of explosive quantities, charge length to diameter ratio, fragment height to diameter ratio, confinement thickness, fragment material and fragment mass. The data was further converted to charge to metal ratio under fragment and confinement. It was observed that, increase in confinement thickness, charge quantity and decrease in fragment height increases the fragment velocity. It is also noted that, charge to metal mass ratio under fragment significantly affects the fragment velocity. At the end, an empirical relationship for fragment velocity interms of all these parameters was established. Using these relations, two velocities 1831.92 m/s and 2523.9 m/s required for NATO STANAG 4496 IM test were estimated. The design parameters for these velocities are presented. Also, the results estimated using the empirical relationship has been compared with published experimental data. Error in the predicted velocities is within the acceptable range. The empirical relationship proposed will be useful for finalization of design of the fragment launch device.     

水下仿生推进器阀控液压摆动关节建模与动态特性分析

采用液压驱动的模拟鱼柔性长背鳍波动运动的水下仿生推进器,当改变液压系统的流量和阀的控制参数时,其运动学参数能够迅速地做相应调整,实现平稳、流畅、连续的仿生运动。建立了阀控液压摆动关节的动力学模型,根据动力学模型得到系统传递函数,并绘制了Bode图。根据传递函数分析了阀控液压摆动关节的稳定特性、动态位置刚度特性和动态响应特性。结果表明阀控液压摆动关节具有一定的自稳定性,其工作频率与影响位置刚度的负载变化频率重叠,动态响应速度可以通过优化结构参数来调整。     

风载荷对某发射装置待发射状态的影响

应用冯.卡门功率谱和谐波合成法生成了考虑脉动效应的瞬时风速时程曲线;计算了发射筒各段的等效风压及等效力矩,给出了作用于发射筒迎风面的风压总值及等效力矩;最后将载荷作为输入条件,进行动力学分析,获得了风载荷作用下发射装置的动态响应。通过分析可知:由于发射装置具有刚度强、质量大的特点,风载荷作用下发射装置的速度、加速度响应均较低,因此,风载荷主要影响发射筒的倾斜程度。     

Research on a MEMS pyrotechnic with a double-layer barrier safety and arming device

As an essential component of ammunition, pyrotechnics can control ignition with high reliability. However, due to limits of fabrication technology, traditional pyrotechnics are bulky. To achieve both functionality and miniaturization, MEMS pyrotechnics integrate initiator, safety-and-arming (S&A) device and lead charge and keep all components within a small size. MEMS S&A devices, as the core component to ensure system safety, are difficult to achieve active and rapid response to control signals with high safety and reliability. In order to overcome the difficulty, we propose the design and characterization of a MEMS pyrotechnic with a double-layer barrier S&A device. The MEMS pyrotechnic is a high-integrated device with an overall size of 13.4 × 8.5 × 5.2 mm³. The initiator is a NiCr bridge foil covered with an Al/CuO energetic film, which can generate flame when ignited by an excitation voltage. To match the flame energy, lead styphnate is chosen in this study as the lead charge. The S&A device contains four semi-circular barriers, which are directly driven by V-shape electro-thermal actuators to gain active control of the pyrotechnics' ignition condition with rapid response. To improve the system's reliability, the four barriers are axisymmetrically placed in two layers, two barriers for each layer, to constitute a double-layer structure with a thickness of 100 μm. The ignition test results show that the S&A device can prevent the initiator from detonating the lead charge in safety condition. In arming condition, the lead charge will be detonated.     

Research on design and firing performance of Si-based detonator

For the chip integration of MEMS (micro-electromechanical system) safety and arming device, a miniature detonator needs to be developed to reduce the weight and volume of explosive train. A Si-based micro-detonator is designed and fabricated, which meets the requirement of MEMS safety and arming device. The firing sensitivity of micro-detonator is tested according to GJB/z377A-94 sensitivity test methods: Langlie. The function time of micro-detonator is measured using wire probe and photoelectric transducer. The result shows the average firing voltage is 6.4 V when the discharge capacitance of firing electro-circuit is 33 μF. And the average function time is 5.48 μs. The firing energy actually utilized by Si-based micro-detonator is explored.     

微电子器件方波EMP注入敏感端对的实验研究

采用方波注入法,对国外某知名公司生产的两个批次的晶体管进行了实验,比较了从CB结反向注入与从EB结反向注入的损伤电压值,发现该类器件的EMP敏感端对与人们一般研究的结论有所不同。     

电磁辐射对桥丝式电火工品性能影响研究

利用传导方法研究射频对桥丝式电火工品的桥丝电阻、烤爆、迟发火以及瞎火等性能影响。研究结果表明,在10％发火功率和0．4MHz的敏感频率条件下,所研究的3种电火工品在照射1～5min后,电阻增加1.2％～7．4％,并且17．3％的试样在照射的过程中出现了烤爆;在对经过照射后的试样进行正常的发火感度试验中,发火时间显著增加,出现了不同程度的迟发火,16．9％的试样瞎火。